‌
Vision · Diligence · Excellence
Grow with Light, Forge China's Instrument Brand
Home > Technology > Instrument Knowledge > Quantum Efficiency vs Faradaic Efficiency: Definitions That Get Confused
2026-11-1790

Quantum Efficiency vs Faradaic Efficiency: Definitions That Get Confused

Quick answer

Quantum efficiency divides product electrons by incident photons; Faradaic efficiency divides product electrons by electrons pushed through the circuit. One photoanode run at 1.2 mA/cm2 under 100 mW/cm2 can score 91.5 % FE, 3.7 % AQY and 1.35 % STH at the same time, and all three are correct.

Two ratios, two denominators

Both metrics answer “how much of the input became product”, but they measure different inputs. Quantum efficiency asks how well the catalyst converts available light, so the denominator is a photon count. Faradaic efficiency asks how selectively the circuit's charge becomes the product you want, so the denominator is a charge count. The numerator is the same in both cases: moles of product multiplied by the electrons each molecule requires.

That is why the two numbers can differ by a factor of thirty without either being wrong. A photoanode that absorbs weakly at 400 nm can convert 92 % of its collected charge into oxygen while using under 4 % of the photons striking it. Reporting only one of them hides whichever half of the problem is worse.

Which metric answers which question

MetricNumeratorDenominatorUnitQuestion it answers
AQY (apparent quantum yield)n × mol productIncident photons in a stated band%How much of the delivered light becomes product
IQE / APCEn × mol productAbsorbed photons%How good the material is, with light absorption removed
IPCECollected electronsIncident monochromatic photons%Wavelength-resolved response of a photoelectrode
FE (Faradaic)n × mol productCharge passed through the external circuit%Selectivity of charge use, only defined with a circuit
STHChemical energy storedIncident solar power, 100 mW/cm2%Bias-free solar fuel performance
Energy efficiencyΔG or ΔH × product rateOptical power in%Thermodynamic accounting across a full device

The electron count n is fixed by the half-reaction and is the most common silent error: 2 for H2 and CO, 2 for formate, 4 for O2, 6 for methanol, 8 for methane, 12 for ethylene. Use 2 for O2 and the calculated efficiency doubles; the arithmetic still looks tidy, which is exactly why it survives to print.

The same run scored three ways

Take a photoanode of 1 cm2 geometric area under 100 mW/cm2 of 365 nm light, held at 1.23 V versus RHE for two hours. Chronoamperometry integrates 8.64 C, which is 8.95 × 10-5 mol of electrons. GC finds 41 µmol of H2, and the incident photon flux over that area is 1.10 mmol/h.

MetricCalculationResult
FE41 µmol H2 × 2 = 82 µmol e-, against 89.5 µmol e- passed91.5 %
AQY82 µmol e- in 2 h, against 2.20 mmol incident photons3.7 %
STH1.2 mA/cm2 × 1.23 V × 0.915 / 100 mW/cm21.35 %

Now put the same chemistry in a slurry reactor with no circuit: 50 µmol/h of H2 under 150 mW/cm2 of 365 nm light over 19.6 cm2. The photon flux is 32.3 mmol/h, the product represents 100 µmol/h of electrons, and AQY is 0.31 %. There is no circuit, so there is no FE. Any “Faradaic efficiency” quoted for that experiment is a relabelled quantum yield, and a reviewer who reads the methods will say so.

Six traps that survive to print

  • FE quoted without a circuit. Powder photocatalysis has no external charge accounting. Report AQY, and reserve FE for photoelectrodes and electrolysers.
  • An unstated photon band. A 300 W xenon source with a 365 nm bandpass delivers roughly 15–20 % of its unfiltered optical power in that band. Compute AQY over the whole spectrum instead of the band and the value drops 3–6×.
  • Incident versus absorbed. A 0.5 g/L slurry absorbs 80–95 % at 365 nm, so APCE is close to AQY. A 300 nm film with 12 % absorbance gives an APCE seven to eight times its AQY. State which one is plotted.
  • FE above 100 % treated as a result. It is not a discovery. Check GC calibration drift, hydrogen crossover in a membrane cell, oxygen ingress from air, and an unmeasured second product such as H2O2.
  • Dark current left in. Subtract the current recorded with the shutter closed before integrating charge; on a small-area electrode it can be a tenth of the photocurrent.
  • AQY measured at high conversion. Above about 10 % conversion, product accumulation and light screening flatten the rate and the ratio stops describing the catalyst. Use the 1–5 % band.

One more discipline helps both numbers: report the measurement uncertainty. A calibrated radiometer contributes 5–7 %, GC calibration 2–3 %, and charge integration under 1 %. Quoting AQY as 3.71 % from inputs that carry 7 % uncertainty is a claim the data cannot support; 3.7 ± 0.3 % is.

Frequently asked questions

Can Faradaic efficiency be higher than quantum efficiency?

Yes, routinely, and in the same experiment. FE compares product to charge, so a photoelectrode with good selectivity but poor light absorption reaches high FE at low AQY. The 91.5 % FE and 3.7 % AQY in the worked example come from one two-hour run.

Why is my FE over 100 %?

Almost always an accounting error rather than a physical one. The usual causes are a GC calibration that has drifted, hydrogen crossing the membrane, oxygen leaking in and being counted as product, or a second product that was never quantified. Re-run the calibration and close the mass balance before reporting.

Is IPCE the same as quantum efficiency?

IPCE is a quantum efficiency measured one wavelength at a time, with the photoelectrode held at a fixed bias, and it counts collected electrons rather than product molecules. For a selective electrode the two agree within a few percent; where they diverge, the missing charge is going to a product you did not measure.

Which number should go in the abstract?

Both, with their conditions. Give AQY at a stated wavelength band and conversion level, and give FE with the charge passed and the cell configuration. A single efficiency figure without its denominator invites the reader to assume the most favourable interpretation.

Related reading

Download
Chat Service
TOP