‌
Vision · Diligence · Excellence
Grow with Light, Forge China's Instrument Brand
Home > Technology > Instrument Knowledge > pH and Ionic Strength in Photocatalytic Hydrogen Production
2026-11-21102

pH and Ionic Strength in Photocatalytic Hydrogen Production

Quick answer

Set pH deliberately, not by default. On TiO2 the point of zero charge is pH 6.0–6.5, so the surface is negative above pH 7 and repels anions. TEOA needs pH 8–11, sulfide/sulfite needs pH 12–13, and methanol works over pH 5–9. A pH move of one unit shifts the hydrogen potential by 59 mV and can change the rate by 20–50 %.

What pH actually changes

Three things move at once, and they pull in different directions, which is why a pH series rarely shows a single clean optimum.

First, surface charge. Below the point of zero charge the oxide surface carries net positive charge and adsorbs anions; above it, the surface is negative and adsorbs cations. For a cationic donor or a metal cation cocatalyst, raising pH past the PZC increases adsorption and can raise the rate. For an anionic donor such as S2- or SO32-, the opposite happens, and the electrostatic penalty is why those systems are run at high pH with a high ionic strength to screen it.

Second, the redox potential of the proton-coupled steps. Both hydrogen evolution and the donor oxidation step shift with pH; a one-unit rise lowers the H+/H2 potential by about 59 mV at 25 °C. If the conduction-band edge shifts by a similar amount, the driving force stays roughly constant and the rate barely moves — which is exactly why pH effects are often attributed to kinetics and adsorption rather than thermodynamics.

Third, the donor's own speciation. This is the largest effect in practice, and it is the one most often left uncontrolled.

pH windows for common donor systems

DonorWorking pHWhy that windowFailure mode outside it
Methanol, 10–20 vol%5–9Neutral molecule, no pKa in range; oxidation is hole-limitedStrong acid dissolves carbonate and changes the surface; strong base accelerates the Cannizzaro side path
TEOA, 5–10 vol%8–11pKa 7.8; the deprotonated amine is the active donorBelow pH 7 the amine is protonated and the H2 rate drops sharply
Na2S / Na2SO3, 0.1–0.35 M12–13Keeps S2- and SO32- deprotonated and suppresses H2SBelow pH 11, H2S forms, the rate falls and the reactor smells of sulfide
EDTA, 1–10 mM5–8Multi-charge anion; needs to be deprotonated to adsorbAcidic conditions protonate it and cut adsorption; it also chelates dissolved metal

Measure the pH after the donor is added, not before. Adding 10 vol% TEOA to water moves pH from 7 to about 10.5 on its own, so a solution described as “neutral with TEOA” is usually already at the top of its window.

Buffers that are not innocent

Many buffers used in photocatalysis are themselves hole scavengers. Tris and EDTA both donate electrons to photoexcited TiO2, so buffering with them adds a second sacrificial agent and inflates the hydrogen rate. Phosphate adsorbs strongly on oxide surfaces and blocks active sites, shifting the apparent PZC and reducing the rate by 10–30 % in some systems.

Borax/boric acid (pH 8–9), carbonate (pH 9–10.5) and dilute NaOH are the safer choices when the buffer must not donate. For the sulfide system, the sulfide/sulfite couple is itself the buffer at pH 12–13, and adding a phosphate buffer only introduces a competing adsorbate.

Record buffer identity and concentration, because “pH 7 phosphate” and “pH 7 unbuffered” are different experiments.

Ionic strength: the second variable

Salt screens surface charge. Raising ionic strength from 1 mM to 0.1 M compresses the double layer from roughly 10 nm to 1 nm and can increase the adsorption of an oppositely charged donor, raising the rate by 20–40 % without any change in pH. Above 0.5 M, powders flocculate, the effective surface area drops and the rate decays during the run.

Choose one salt, use it across the whole series, and report the concentration in mol/L. NaCl is fine for most oxide systems; avoid chloride with silver-based cocatalysts, and avoid sulfate when the anion is also a donor. Keep ionic strength constant while varying pH, otherwise the two effects are inseparable and the pH trend you report is partly a salt trend.

A pH protocol that holds up

  • Prepare the donor solution, then adjust pH with NaOH or HCl, then add catalyst. Adjusting after the powder is in suspension gives a reading dominated by the slurry, not the solution.
  • Equilibrate 30 min in the dark before illumination, and measure pH again at that point. Adsorption of the donor on the oxide typically shifts pH by 0.2–0.6 units.
  • Measure pH at the end of the run. Unbuffered sulfide and TEOA systems drift 0.5–1.5 units over 4 h as the donor is consumed, and a rate quoted at the starting pH then describes conditions that no longer existed.
  • Run at least three pH values spanning the window, with everything else fixed, including irradiance in mW/cm2 and catalyst loading in g/L.

Report pH, buffer, ionic strength and the drift together. A single “pH 7” in a methods section is not enough to reproduce the rate, and it is the first thing to check when another group reports a different number for the same catalyst.

Frequently asked questions

What pH is best for photocatalytic hydrogen production?

It depends on the donor, not on the catalyst alone. Methanol works over pH 5–9, TEOA over 8–11 because its pKa is 7.8, and Na2S/Na2SO3 needs 12–13 to stay deprotonated. Pick the window from the donor, then optimise within it.

Does pH change the band gap?

It shifts the band edges rather than the gap. Both the conduction and valence band edges move by roughly 59 mV per pH unit at 25 degrees Celsius, so the driving force for hydrogen evolution is nearly pH-independent while adsorption and surface charge are not.

Should I buffer the solution?

Only with a buffer that does not donate holes. Borate and carbonate are acceptable; Tris and EDTA are sacrificial agents and will inflate the rate. Unbuffered runs are fine if you report the starting and ending pH, since TEOA and sulfide systems drift 0.5–1.5 units over a few hours.

Why did my rate drop when I moved to pH 3?

At pH 3 the oxide surface is positively charged and repels anionic donors, and many oxide supports begin to dissolve. Check the filtrate by ICP for dissolved metal before attributing the drop to a change in mechanism.

Related reading

Download
Chat Service
TOP